The data loggers can be used for various application within the life scrunch and food and beverage industries.
When used with our Temperature Thermocouple Sensor, the following application(s) are covered:
Temperature Range of
-50 to +62 °C
Live Data Option Available
Interchangeable Sensor Design
TrackSense Pro Wireless Data Logger
Temperature Thermocouple Sensor
Ellab’s unique Temperature Thermocouple Sensor (TC Sensor) now allows users worldwide to use thermocouples in conjunction with wireless data loggers. The sensor has a temperature range of -50 to +62 °C. The Temperature Thermocouple Sensor is especially designed for applications that cause a lot of strain on sensors and require as little impact on samples as possible. A good example of said applications would be Lyophilization, also known as Freeze-drying.
The TrackSense Pro data logger series are equipped with an Interchangeable sensor option, unlocking several measuring parameters:
✓ Temperature
✓ Pressure
✓ Conductivity
✓ Relative humidity
✓ Vacuum
✓ Steam Penetration
The data loggers can easily be activated and read by the Multi reader station and combined with the Sky module for real time data via wireless communication.
Thermocouple Wire
The thin thermocouple wire itself has a temperature range of -196 to + 200 °C and is equipped with a “naked tip” that takes up next to no room within a sample and provides users with a faster response time. In addition to this, the wire comes in 10, 30, 50 and 100 cm lengths (30 cm standard), offering an additional layer of versatility. The data logger in combination with the mounted sensor has a temperature range of -50 to +62 °C and is calibrated from -60 to +60 °C with a state of the art accuracy of ±0.3 °C.
Increased Temperature Range
When keeping the data logger at ambient temperature, it is also possible to insert a wired sensor into other applications that require a wider temperature range. By using standard type T thermocouple sensors in various materials and lengths, the highly versatile Temperature Thermocouple Sensor can cover a temperature range of -50 to +400 °C.
Replace Thermocouple Sensors with Ease
The feature that makes this sensor highly unique, is the ability to have the thermocouple wire replaced via a screw terminal after a prolonged series of use. Typically, if wires get strained through rough handling or immensely demanding applications, the entire sensor head would have to be replaced – now with the Temperature Thermocouple Sensor, bundles of thermocouple wires can easily be acquired through Ellab and replace the single damaged wire, resulting in a far more cost-efficient process.
Key Features and Benefits
One logger - multiple sensor options
21 CFR Part 11 Compliant
Real time data with the SKY module
User-friendly validation software
Can be steam sterilized
Replaceable thermocouple wires
Increased temperature range when using various type T thermocouples
Sensor with this logger configuration:
Temperature Thermocouple Sensor*
Temperature Measuring Range:
-50 to +62 °C (Calibrated from -60 to
+60 °C)
-196 to +400 °C when keeping the logger at ambient temperature and using appropriate thermocouple wire
Measuring Principle:
Thermoelectric Effect
Sensor Element:
Thermocouple Type T
Accuracy:
± 0.3 °C Calibrated
Position of Measuring Point from Tip:
0 mm
Cable Length:
10, 30, 50 or 100 cm
Cable Dimensions and Type:
0.55 x 0.95 mm type AWG30 with naked tip
Sensor Response Time:
T-63%:
0.03 Second
T-90%:
0.09 Second
*Requires ValSuite® 5.1.0.11 or later and logger firmware version 26.9 or later
Logger with this sensor configuration:
Pro 3G
Operating Temperature:
-50 to +62 °C
Operating Pressure:
0.001 mBar to 4 Bar ABS
House Material:
316 L Stainless Steel
Diameter:
25 mm
Length:
44 mm
Weight With Battery:
48 Grams
Memory Capacity:
120,000 Data Points / 40,000 Samples
Minimum Sample Rate:
1 Second
Maximum Sample Rate:
24 Hours
Maximum Start Delay:
14 Days
Intrinsically Safe:
Ex II1GD Ex ia IIC T3 Ga, -50 °C ≤ Tamb ≤ +105 °C
Time Accuracy:
± 5 Seconds Per 24 Hours
Battery:
Please Note: If equipment is used in ATEX environment, special conditions for safe use stated in ATEX certificates section 17 must be considered.
The ValSuite® Software
ValSuite is our reputable validation and calibration software. This intuitive software combines all our equipment systems into a single platform. Thereby opening the door to a vast amount of new possibilities by allowing you to combine data loggers with the traditional thermocouple systems.
We offer multiple versions of ValSuite to meet your exact needs. Most notably ValSuite Pro, our FDA 21 CFR Part 11 compliant software that ensures full data integrity.
ValSuite offers features like customized reports with clear pass/fail criteria, test templates, data analysis, monitoring, live data and much more. ValSuite is developed according to GAMP principles and is available in multiple languages for Windows 7, 8 and 10 (32/64-Bit). ValSuite is availabe in four generic versions: ValSuite Basic, ValSuite Medical, ValSuite Plus and ValSuite Pro.
Highlighted Features
Suitable Applications
Ellab Applications
Ellab provides a wide range of diverse products and solutions for the pharmaceutical, medical and food industries all around the world.
See all applicationsSuitable Accesories
Ellab offers a wide range of customizable fittings and essential accessories for processes and studies within different industries. By using one of our unique fittings, loggers can be applied to hard-to-reach areas, cold spots and other critical measuring points.
Ellab Accesories
Ellab offers a wide range of customizable fittings and essential accessories for processes and studies within different industries.
See all Accesories